CIM ECO 1000
Description
CIM ECO 1000 is a LEED-accredited, liquid applied urethane coating that:
- Cures in hours to form a tough elastomeric coating
- LEED and CDPH-compliant material (earns LEED points)
- 100% solids, zero VOC
- Adheres to most substrates
- Forms a chemical and abrasion-resistant barrier for waterproofing, corrosion protection, and containment of water and most aqueous chemicals.
Features & Benefits
| Excellent Concrete Crack Bridging | Bridge new cracks up to ¼ inch |
| Liquid applied | Easily conforms to irregular shapes |
| Bonds to most substrates | Excellent adhesion provides a fully bonded waterproofing system |
| Lowest permeability in industry | Designed for constant immersion environments |
| 100% solids/Zero VOC | Compliant to toughest VOC regulations |
| UV stable | Suitable for applications in direct contact with UV |
Need more information?
CIM ECO 1000 FAQS
For areas where a higher viscosity trowel grade product is required, CIM 1000 Trowel is recommended.
Yes. CIM ECO 1000 is compatible with other CIM coatings and primers.
Yes. CIM ECO 1000 can be used to repair existing CIM using the standard surface preparation recommendations for repairing existing CIM membranes.
Yes. The same warranties are available for both CIM 1000 and CIM ECO 1000
CIM ECO 1000 does not contain solvent and does not require the use of intrinsically safe tools. In many cases, respirators are not required to use CIM ECO 1000 provided the space is adequately ventilated and the coating is not being sprayed. Use of a respirator should be evaluated for each enclosed space based on tank size, coated area, ventilation, and application technique.
Yes. Respirators are required when spraying CIM ECO 1000
CIM ECO 1000 is black in color. Contact your local CIM representative for options for using pigmented topcoats with CIM products.
No. For applications requiring potable water approvals, please consider CIM 1061.
CIM ECO 1000 comes in kits the are pre-portioned in the correct mix ratio. Always add one full jug of Activator to a full pail of Premix. Do not mix partial kits as this can effect the curing and physical properties of the product.
The theoretical coverage rate of CIM ECO 1000 depends on the thickness applied.
- 123 ft2 at 60 mil
- 92 ft2 at 80 mil
- 73 ft2 at 100 mil
- See the coverage calculator
CIM ECO 1000 is designed for use on concrete, wood, and steel surfaces. Use of CIM EMT Primer or CIM ECO Primer is recommended to achieve the best adhesion and minimize the effect of moisture in the substrate.
In some circumstances CIM ECO 1000 can be applied without primer if the substrate moisture content is low. However, using primer is required when the substrate has high moisture content or when the strong possible adhesion is required. CIM EMT Primer and CIM ECO Primer will both reduce pinholes and improve adhesion for CIM ECO 1000.
CIM ECO 1000 does not contain solvents and is free of VOC’s
Yes. CIM ECO 1000 currently meets LEED V4.1 requirements for VOC’s and indoor air quality (CDPH 01350) and by soon to be released LEED V5.
Yes. CIM ECO 1000 can be applied to vertical surfaces at a reduced thickness. To achieve the full thickness, 2 or 3 coats are typically needed.
CIM ECO 1000 can be applied at 50°F (10°C) or higher as long as the surface temperature is at least 5°F (3°C) higher than the dew point. CIM ECO 1000 may be preheated to facilitate application when the temperature is below 60°F (15°C), but the working time may be reduced. At high ambient temperatures, CIM ECO 1000 can still be applied but may have a reduced working time during application.
CIM ECO 1000 can typically be placed into service 24-48hr after installation, though the exact cure time depends on the temperature.
Let’s connect and never miss an update or news from us.
 |
 |
 |
If you have already registered, please login to view SDS files.
