Synthetic Rubber 1B59 Sharp Edge Coverage
HumiSeal® 1B59 Sharp Edge Coverage is an air drying, single component, synthetic rubber conformal coating. HumiSeal® 1B59 SEC is formulated to provide increased coverage on component edges, when compared to other similar coatings. HumiSeal® 1B59 SEC is formulated for effective application using atomized spray application methods, although other methods can also be used.
HumiSeal® 1B59 SEC demonstrates the following advantages:
- Excellent coverage of sharp edge components.
- Extremely low moisture vapor permeability.
- Protection against moisture, salt / corrosive environments, and dirt.
- Improved thermal stability compared with other conformal coatings.
- Excellent flexibility putting low stress on components.
- 在紫外线下会发出荧光,便于检查,而且容易修复。
Properties of HumiSeal® 1B59 SEC Liquid Coatings
财产 | 价值 |
密度,根据ASTM D1475 | 0.84 ± 0.02 g/cm3 |
Solids Content, % by weight per ISO3251 | 17 ± 2 % |
Viscosity, per ASTM D2196 (dependant on shear) | 200 to 2000CPS at 25ºC |
VOC | 697.2 grams/litre |
Drying Time to Handle, per Fed-Std-141, Meth. 4061 | < 20 minutes |
室温下的保质期,从DOM开始 | 6个月 |
Properties of HumiSeal® 1B59NSLU Cured Coatings
财产 | 价值 |
建议涂层厚度 | 25 - 75 microns |
建议的固化条件 | 24小时@RT或30分钟@76°C |
推荐的剥离剂 | HumiSeal®剥离器1080 |
最低工作温度 | -65ºC |
最高工作温度 | 150ºC |
玻璃转化温度 - DSC | -50ºC |
模数 - DMA | 75 MPa @ -40°C 20 MPa @ 20°C |
Elongation at -40°C | 200% |
Elongation at 23°C | 450% |
绝缘耐受电压,根据MIL-I-46058C标准 | >1500伏 |
Surface Insulation Resistance 85C/85% RH IPC CC 830 | 9.5 Log10 Ohms |
Application of HumiSeal® 1B59 SEC
Conformal coatings can be successfully applied to boards that have been cleaned prior to coating and also to boards assembled using low residue “no clean” assembly materials. Users should perform adequate testing to confirm compatibility between the conformal coating and their particular assembly materials, process conditions and cleanliness level. Please contact HumiSeal for additional information.
HumiSeal® 1B59 SEC is specifically formulated to shear during application to a viscosity suitable for atomized spray application. No additional dilution is required. HumiSeal® Technical Support should be contacted if any further advice on application methods is required.
Storage
HumiSeal® 1B59 SEC should be stored away from excessive heat or cold, in tightly closed containers. HumiSeal® products may be stored at temperatures of 0 to 35°C. Prior to use, allow the product to equilibrate for 24 hours at a ambient temperature.
注意事项
HumiSeal®保形涂料的应用应按照当地和国家的健康和安全法规进行。
The solvents in HumiSeal® Conformal Coatings are flammable. Material should not be used in presence of open flame or sparks. Use only in well-ventilated areas to avoid inhalation of vapours or spray. Avoid contact with skin and eyes.
Consult MSDS/SDS prior to use.